✓ Schluter Certified✓ Mapei Certified✓ Owner-Operated✓ Ottawa & Orléans✓ Free Quotes

Ottawa & Orléans

Custom Tile Showers in Ottawa

Walk-in showers built correctly — KERDI waterproofing, flood-tested, precision-cut on the PIKUS 130 bridge saw.

Custom walk-in showers in Ottawa, built correctly from the ground up. I use Schluter KERDI waterproofing membrane — properly lapped, embedded in unmodified thinset, and flood-tested for 24 hours before any tile is set. Niche cutouts, L-cuts, and all detail work are made on the PIKUS 130 bridge saw for clean, tight-fitting edges that close properly and look finished. No subcontractors — every step done by Joseph Leger personally.

What I Build

Custom Shower Features

Walk-In Showers

Custom-sized walk-in showers built to your bathroom layout — curbless, curbed, or offset entry, all properly waterproofed and sloped to drain.

Niches (Internal Stop-Cuts)

Recessed niches cut precisely into the wall cavity and waterproofed independently. Stop-cuts and internal L-cuts made on the PIKUS 130 for clean edges that tile fits tight against.

Bench Seats

Tiled bench seats built and waterproofed as part of the shower assembly — not an afterthought bolted on after the fact.

Linear Drains

Linear drain installation with correct single-plane slope from the far wall — no crowned floors, no standing water.

Full-Height Tile

Floor-to-ceiling tile with consistent joint width, plumb grout lines, and Schluter profiles at all transitions and outside corners.

Feature Walls

Floor-to-ceiling accent walls or feature panels — large format tile, book-matched stone-look porcelain, or mixed material combinations.

The Critical Step

The Waterproofing Process

Waterproofing is the most important part of any tile shower build. Get it wrong and you get rot, mold, and structural damage hidden behind tile — damage that doesn't show up for months or years, and costs far more to repair than a shower done right the first time.

Where I Work

Custom Shower Service Areas

Serving Ottawa and surrounding communities for custom tile shower builds.

Ottawa Orléans Kanata Barrhaven Gloucester Nepean Rockland Cumberland Avalon Fallingbrook Chapel Hill Convent Glen Beacon Hill Blackburn Hamlet Vanier

Common Questions

Custom Tile Shower FAQ

How do you waterproof a tile shower?
I use Schluter KERDI membrane — a sheet-applied waterproofing membrane embedded directly into the thinset mortar bed. Every seam is lapped a minimum of 2 inches and set in unmodified thinset. Corners and pan-to-wall transitions get KERDI-BAND treatment. Once installed, the shower pan is flood-tested for 24 hours before any tile is set. If the water level drops, I find the source and repair it before proceeding.
Can you build shower niches in Ottawa?
Yes. Niches are built into the wall cavity and waterproofed as part of the shower assembly — not surface-mounted or added after the fact. All cuts, including internal stop-cuts and L-cuts for niche edges, are made on the PIKUS 130 bridge saw for clean, tight-fitting tile that looks finished and holds grout properly.
What tile types work best for showers?
For shower floors, a tile with a COF (coefficient of friction) rating of 0.42 or higher (ANSI A137.1) is required for safety in wet conditions. For walls, porcelain tile is the most durable and moisture-resistant option. Large-format tiles (24×48 and larger) are popular and work well if the substrate is flat enough — which is part of what I assess during the quote visit. I help you select tiles that work for the application, not just tiles that look good in a showroom.

Start Your Project

Get a Free Custom Shower Quote

I visit in person, measure the space, and give you a written quote. No surprises, no subcontractors.

(613) 981-8903 Send a Message

See the full service details on the Custom Tile Showers service page.